5 Free Circuit Simulator Apps for Android

Here is a list of 5 free circuit simulator apps for Android. Designing and simulating a circuit can be a complicated task but it can be done on an Android device. There are decent apps available on the Play Store covering a wide range of features. I covered 5 such apps that you can use to design basic logic gates to complex electronic circuits.

All these apps offer various electronic components necessary for circuit designed. With those components, you can design the circuit and simulate it. These apps offer AC, DC, Transient circuit analysis, and SPICE simulation. During the simulation, you can check the various reading like voltages, currents, and other variables.

Some of these apps also allow you to use your device’s components in the circuit such as proximity sensor, accelerometer, microphone, charging, etc. During the simulation, the apps take input from the device in real-time. Apart from simulation and analysis, some of these apps can also create circuit schematics that you can print or export to PDF.

My Favourite Circuit Simulator App for Android

I couldn’t pick a favorite from these 5 circuit simulator apps. Because circuit simulation is more about the components and features rather than functionality. All these apps have similar functionality but with different sets of features. Here I listed different types of components and features these apps offer. You can go through the lists and pick an app best suited for your specific needs.

You can also check out our list of best free Flight Simulator AppsSteganography Apps, and Logo Design Apps for Android.

CircuitSafari SPICE Simulator

CircuitSafari SPICE Simulator is a free comprehensive circuit simulator app for Android. This app is great for circuits with sub-circuits under those. It makes it easy to layout components and make a custom component library that can be re-used in the app. It can capture the circuit schematic and create a PDF for the same. Users can create big circuits with interactive component adjustments and display the results while the simulation is going on. It can also export a netlist that can be imported directly into KiCad Pcbnw for PC board layout. Apart from the built-in components, the app can also use the device for Accelerometer, Buzzer, Frame, Memory, Microphone, Serial Port, Solar Cell, Speaker. Users can create add a component for the same in the circuit and the app uses the actual device components during simulation.

Available Components:

  • Resistors, Capacitors, Inductors
  • Voltage, Current Source
  • Ground
  • Label
  • Pin
  • Scope Probe
  • Voltmeter, Ammeter, Wattmeter, Ohnmeter, Frequency Meter, Distortion Meter
  • Diode (NPN, PNP, N Channel Mosfet, P Channel Mosfet, NChannel Jfet, P Channel Jfet)
  • Transmission Line
  • Current/Voltage Controlled Current/Voltage Source
  • Switch
  • Relay
  • Fuse
  • Laplace block
  • Summer, Multiply
  • Logic Gates
  • Tristate Buffer
  • Flip Flop
  • Multi-channel oscilloscope (linear and logarithmic view)
  • LEDs
  • 7-Segment, Bar, Dot Matrix Displays
  • Potentiometer
  • Text

Main Features:

  • Import standard spice models
  • AC, DC, Transient circuit analysis
  • Hierarchical schematics with schematics spanning
  • Full autorouting for schematic capture
  • Cut, copy, paste circuits
  • Create subcircuits
  • Add expressions in component parameters
  • Interactive component adjustment
  • Visualize simulation progress on LEDs, Displays
  • Create and use a custom component library
  • Generate PDF of schematics
  • Example circuits
  • Export netlist for PC board layout
  • Google Drive integration

Electric Circuit Studio

Electric Circuit Studio is another free circuit simulator app for Android. This is a very capable app that can be used to simulate simple logic gates to complex electronic circuits. It packs a variety of electronic components in a simple UI where users can easily find and add components to the grid to create a circuit. Along with the components, this app packs different types of calculators, various electronic resources, and a wide range of connector pinouts. Last but not least, it can create circuit schematics with SPICE analysis.

Available Components:

  • Resistors, Capacitors, Polarized Capacitors, Inductors
  • Current & Voltage Sources (DC, Pulse)
  • Diode, Zener Diode
  • LED
  • Transistors (PNP, NPN, NMOS, PMOS, NJFET, PJEFT)
  • Gates (AND, OR, NOT, NOR, XOR, XNOR, NAND)
  • SR Latch
  • Flip Flop (D, T, JK)
  •  Operational Amplifier
  • Timer
  • LM317, LM337, 7805, 7905, VCVS, VCCS, CCVS, CCCS
  • Potentiometer
  • Transformer
  • Switch (SPDT, SPST)
  • Button
  • Replay
  • Crossover
  • Calculators (Ohm’s Law, Y-Delta Transformation, Power, Voltage, Current Divider, RLC reactance/impedance, LC resonance, and more)
  • Connector Pinout (VGA, HDMI, THuderbold, Apple Lightning, SATA, eSATA, SD Cards, SIM cards, Ethernet, Reapberry GPIO, etc.)
  • Resources (Ampacity, Resistivity, Resistor values, Capacitor codes, Capacitor values, Voltage regulators, etc.)

Main Features:

  • Schematic editor and SPICE simulator
  • AC, DC, Transient analysis
  • Undo, Redo
  • Take Screenshots
  • Export Circuit
  • Interactive Guides

PROTO - Circuit Simulator

PROTO – Circuit Simulator is a free circuit simulator app for Android. This is one of the best apps to simulate the electronic circuit in real-time and observes its behavior. During the simulation, users can check various parameters in real-time such as current, voltage, etc. This app packs a wide set of components to simulate various types of electronic circuits.

Available Components:

  • AC, DC, Pulse, Noise Voltage Source, Triangle, Square
  • Potentiometer
  • Current source
  • Capacitor, Resistor
  • Photoresistor
  • Memristor
  • Transformer
  • Inductor
  • Digital Gates (AND, OR, NOR, XOR, NAND, Inverter)
  • Logic Input
  • Analog to Digital converter
  • Transistor (PNP, NPN, N, P channel Mosfet)
  • Diode (LED, Schottky, Zener, rectifying diode)
  • Switches (Relay, SPST)
  • Bulb, Fuse
  • Timer
  • Operational amplifier
  • Ammeter, Voltmeter
  • Accelerometer
  • FM source

Main Features:

  • Current and Voltage flow animations
  • Adjust circuit parameters (current, voltage, etc.)
  • Four-channel osciloscope
  • Copy components
  • Play/Pause Simulation
  • Learning Examples

Logic Circuit Simulator Pro

Logic Circuit Simulator Pro is a free circuit simulator app for Android. This app offers a wide range of electronic components. It includes tips for using the components and educational tutorials with examples. Users can create multiple circuits and embed circuits in each other. The app also comes with themes to customize the UI combined with a dark mode. Additionally, this app can use the device sensor for inputs and output. This includes Charge Detector, Sensors (Accelerometer, Proximity, Magnetic Field, Pressure, Battery), Tilt Detector, Noise Meter, and Media Volume Button Detector.

Available Components:

  • Digital Gates (AND, OR, NOR, XOR, NAND, XNOR NOT)
  • Buffer Gate
  • 3 Input Logic Gates
  • IC
  • Programmable Array Logic (PAL)
  • Programmable Logic Array (PLA)
  • ROM
  • MUX, DEMUX
  • High & Low Logic Constant
  • Nodes
  • Frequency Generator (0.5Hz, 1Hz, 40Hz, 1kHz, 50kHz)
  • Toggle Switch
  • Pulse Button
  • Bulb, RGB Light
  • 7-Segment Display
  • BCD to 7-Segment Display Decoder
  • 14-Segment Display
  • LED Dot Matrix
  • Texts
  • Flip-Flop (SR, D, JK, T)
  • Latch (SR, Dl JK, T)
  • SR Gate Latch
  • Timer

Main Features:

  • Grid
  • Snap component to the grid to position
  • Multi-selection mode
  • Undo, Redo, Cut, Copy, Paste functions
  • Tutorials
  • Import/Export projects

Logic Circuit Simulator Mobile

Logic Circuit Simulator Mobile is another free circuit simulator app for Android. This app is limited to logic gates only. The app is fairly simple to use where users can add a component from the list. Then pick the circuit tool and tap on the ends to close the circuit. Once the circuit is designed, users can just tap on a logic gate to change its state and simulate the circuit.

Available Components:

  • Gates (AND, OR, NOT, NOR, NAND, XOR, XNOR, BUFFER)
  • One Bit Monitor
  • Toggle Button
  • Flip Flop (D, T, SR, JK)
  • Low & High Constant
  • Clock
  • 4×1 Multiplexer, Demultiplexer
  • 7-Segment Display, 8×8 LED Matrix Display
  • BCD to 7-Segment Display

Main Features:

  • 1-tap to simulate logic gates
  • Snap to create circuit
  • Example Projects
Shobhit
Related Posts
Write a Comment

About Us

Sample image

We are the team behind some of the most popular tech blogs, like: I LoveFree Software and Windows 8 Freeware.

More About Us
SEO Service